SAFETY DATA SHEET – MINERAL PAINT
ISSUED NOVEMBER 2019
ISSUED NOVEMBER 2019
Product Name: Mineral Paint
NON-HAZARDOUS ACCORDING TO THE CRITERIA OF WORKSAFE AUSTRALIA
GECA Accredited
Recommended Use: Surface coating. Applied by brush or roller or spray gun.
Supplier: Blacksquare Design Pty Ltd T/A Made By Paint
ABN: 17 127 539 655
Address: PO Box 1287 Kenmore Qld 4069
Tel: 0400740540
HAZARDS
Not classified as hazardous according to criteria of Safe Work Australia. Not a Dangerous Good according to Australian Dangerous Goods (ADG) Code, IATA or IMDG/IMSBC criteria. Non-Hazardous. Poisons Schedule: None allocated
COMPOSITION OF INGREDIENTS
Components CAS No. Proportion
Acrylic polymer – 30-60%
Non hazardous ingredients various to 100%
Pigments various 30-60%
FIRST AID MEASURES
General Information: You should call The Poisons Information Centre if you feel that you may have been poisoned, burned or irritated by this product. The number is 13 1126 from anywhere in Australia and is available at all times. Have this SDS with you when you call.
Inhalation: First aid is not generally required. If in doubt, contact a Poisons Information Centre or a doctor.
Skin Contact: Irritation is unlikely. However, if irritation does occur, flush with lukewarm, gently flowing water for 5 minutes or until chemical is removed.
Eye Contact: No effects expected. If irritation does occur, flush contaminated eye(s) with lukewarm, gently flowing water for 5 minutes or until the product is removed. Obtain medical advice if irritation becomes painful or lasts more than a few minutes. Take special care if exposed person is wearing contact lenses.
Ingestion: If product is swallowed or gets in mouth, do NOT induce vomiting; wash mouth with water and give some water to drink. If symptoms develop, or if in doubt contact a Poisons Information Centre or a doctor.
Medical Attention & Special Treatment
Treat symptomatically.
Fire and Explosion Hazards: The major hazard in fires is usually inhalation of heated and toxic or oxygen deficient (or both), fire gases. There is no risk of an explosion from this product under normal circumstances if it is involved in a fire. This product is likely to decompose only after heating to dryness, followed by further strong heating. Fire decomposition products from this product are likely to be irritating if inhaled.
Extinguishing Media: Not combustible. Use extinguishing media suited to burning materials.
Fire Fighting: If a significant quantity of this product is involved in a fire, call the fire brigade.
Flash point: Does not burn.
Upper Flammability Limit: Does not burn.
Lower Flammability Limit: Does not burn.
Auto ignition temperature: Not applicable – does not burn.
Flammability Class: Does not burn.
Accidental release: Minor spills do not normally need any special cleanup measures. In the event of a major spill,prevent spillage from entering drains or water courses. As a minimum, wear overalls, goggles and gloves. Suitable materials for protective clothing include rubber, PVC. Eye/face protective equipment should comprise as a minimum, protective glasses and preferably, goggles. If there is a significant chance that vapours or mists are likely to build up in the cleanup area, we recommend that you use a respirator. Usually, no respirator is necessary when using this product. However, if you have any doubts consult the Australian Standard mentioned below. Stop leak if safe to do so, and contain spill. Absorb onto sand, vermiculite or other suitable absorbent material.
If spill is too large or if absorbent material is not available, try to create a dike to stop material spreading or going into drains or waterways. Sweep up and shovel or collect recoverable product into labelled containers for recycling or salvage, and dispose of promptly. Recycle containers wherever possible after careful cleaning. After spills, wash area preventing runoff from entering drains. If a significant quantity of material enters drains, advise emergency services.
This material may be suitable for approved landfill. Ensure legality of disposal by consulting regulations prior to disposal. Thoroughly launder protective clothing before storage or re-use. Advise laundry of nature of contamination when sending contaminated clothing to laundry.
HANDLING AND STORAGE
Keep exposure to this product to a minimum, and minimise the quantities kept in work areas. Make sure that containers of this product are kept tightly closed.
EXPOSURE CONTROLS/PERSONAL PROTECTION
The following Australian Standards will provide general advice regarding safety clothing and equipment: Respiratory equipment: AS/NZS 1715, Protective Gloves: AS 2161, Occupational Protective Clothing: AS/NZS 4501 set 2008, Industrial Eye Protection: AS1336 and AS/NZS 1337, Occupational Protective Footwear: AS/NZS2210.
SWA Exposure Limits TWA (mg/m3) STEL (mg/m3) Exposure limits have not been established by SWA for any of the significant ingredients in this product. No special equipment is usually needed when occasionally handling small quantities. The following instructions are for bulk handling or where regular exposure in an occupational setting occurs without proper containment systems.
Ventilation: This product should only be used in a well ventilated area. If natural ventilation is inadequate, use of afan is suggested.
Eye Protection: Eye protection such as protective glasses or goggles is recommended when this product is being used.
Skin Protection: The information at hand indicates that this product is not harmful and that normally no special skin protection is necessary. However, we suggest that you routinely avoid contact with all chemical products and that you wear suitable gloves (preferably elbow-length) when skin contact is likely.
Protective Material Types: We suggest that protective clothing be made from the following materials: rubber, PVC.
Respirator: Usually, no respirator is necessary when using this product. However, if you have any doubts consult the Australian Standard mentioned above. Safety deluge showers should, if practical, be provided near to where this product is being handled commercially.
PHYSICAL AND CHEMICAL PROPERTIES
Physical state: Viscous liquid
Colour: White.
Odour: Mild, characteristic odour.
Solubility: Miscible with water
Specific Gravity: 1.35-1.45 kg/Litre @20°C
Relative Vapour Density As for Water
Vapour Pressure 2.37 kPa at 20°C (water vapour pressure).
Flash Point (°C): Not applicable
Flammability Limits (%): Not applicable
Auto ignition Temperature (°C): Does not burn
% Volatile by Weight: Not available
Solubility in water (g/L): Miscible
Melting Point/Range (°C): Not applicable
Boiling Point/Range (°C): 100 (water)
Decomposition Point (°C): Not available
pH: 8.5-9.5
Viscosity: Not available
Evaporation Rate: As for Water
STABILITY AND REACTIVITY
Reactivity: This product is unlikely to react or decompose under normal storage conditions. However, if you have any doubts, contact the supplier for advice on shelf life properties.
Conditions to Avoid: Keep containers tightly closed.
Incompatibilities: Oxidising agents.
Fire Decomposition: This product is likely to decompose only after heating to dryness, followed by further strong heating. Combustion forms carbon dioxide, and if incomplete, carbon monoxide and possibly smoke. Water is also formed. Carbon monoxide poisoning produces headache, weakness, nausea, dizziness, confusion, dimness of vision, disturbance of judgment, and unconsciousness followed by coma and death.
Polymerisation: This product will not undergo polymerisation reactions.
TOXICOLOGICAL INFORMATION
Inhalation: Available data indicates that this product is not harmful. In addition product is unlikely to cause any discomfort or irritation. High dust levels (from sanding) may irritate the skin, eyes, nose and throat. No data for health effects associated with long term inhalation.
Skin Contact: Available data indicates that this product is not harmful. It should present no hazards innormal use. However product may be mildly irritating, but is unlikely to cause anything more than mild discomfort which should disappear once contact ceases. No data for health effects associated with long term skin exposure.
Eye Contact: This product may be irritating to eyes, but is unlikely to cause anything more than mild transient discomfort. No data for health effects associated with long term eye exposure.
Ingestion: Significant oral exposure is considered to be unlikely. However, this product may be irritating to mucous membranes but is unlikely to cause anything more than transient discomfort. No data for health effects associated with long term ingestion.
Carcinogen Status:
SWA: No significant ingredient is classified as carcinogenic by SWA.
NTP: No significant ingredient is classified as carcinogenic by NTP.
IARC: No significant ingredient is classified as carcinogenic by IARC.
DISPOSAL CONSIDERATIONS
Containers should be emptied as completely as practical before disposal. If possible, recycle product and containers either in-house or send to recycle company. If this is not practical, send to a commercial waste disposal site.
TRANSPORT INFORMATION
This product is not classified as a Dangerous Good by ADG, IATA or IMDG/IMSBC criteria. No special transport conditions are necessary unless required by other regulations.
REGULATORY INFORMATION
AICS: All of the significant ingredients in this formulation are compliant with NICNAS regulations.
OTHER INFORMATION
Acronyms:
ADG Code Australian Code for the Transport of Dangerous Goods by Road and Rail (7th edition)
AICS Australian Inventory of Chemical Substances
SWA Safe Work Australia, formerly ASCC and NOHSC
CAS number Chemical Abstracts Service Registry Number
Hazchem Code Emergency action code of numbers and letters that provide information to emergency
services especially firefighters
IARC International Agency for Research on Cancer
NOS Not otherwise specified
NTP National Toxicology Program (USA)
R-Phrase Risk Phrase
SUSMP Standard for the Uniform Scheduling of Medicines & Poisons
UN Number United Nations Number
This SDS summarises to our best knowledge at the date of issue, the chemical health and safety hazards of the material and general guidance on how to safely handle the material in the workplace. Since we cannot anticipate or control the conditions under which the product may be used, each user must, prior to usage, assess and control the risks arising from its use of the material.
If clarification or further information is needed, the user should contact Blacksquare Design P/L.
Blacksquare Design P/L’s responsibility for the material as sold is subject to the terms and conditions of sale, a copy of which is available upon request.
Blacksquare Design P/L disclaims responsibility for damage of any kind resulting from the use of this information.
THERE ARE NO WARRANTIES OR REPRESENTATIONS, EXPRESSED OR IMPLIED, INCLUDING THOSE OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THIS INFORMATION OR TO
THE PRODUCT IT DESCRIBES.